Configuring Asset Movement

Asset Movement

You can configure movement type for an asset such as Return movement type or Default movement type for tracking the movement of asset. The default movement type includes Store Movement, Floor Movement, From Repair, and To Repair. The return movement type process includes the various reasons for returning the assets.

When any of these movements are initiated, a workflow can be triggered to obtain as many as 10 levels of approvals.

Configurations

Movement Configuration needs to be set up for all the Asset Movement types and specific Asset Movements as described in the following section.
Location-wise Approvers need to be mapped (see: Configuring Location-wise Approvers).
Approvals can be enabled or disabled for each Asset Category through the Approval Configuration setting (see: Approval Configuration).

To configure Asset movement approval matrix:

Select Asset > Configuration > Others > Movement Configuration.
On the MOVEMENT CONFIGURATION page, click ADD NEW on the ACTIONS panel.
Select the Tenant and Movement Type. Based on the movement type selection (Return Type or Default Type), a workflow is triggered to complete the configuration.
Figure: Movement Configuration
Click SUBMIT.

Return Type Movement

If movement type is selected as Return Type Movement, the following fields are displayed as shown in the figure below:

Figure: MOVEMENT CONFIGURATION page (Return Type Movement)

Field Description for Return Type Movement

The following table describes the fields on the Return MOVEMENT CONFIGURATION page:

Field	Description
Movement Type	Select Movement type as Return Type Movement.
Type	Select the type from the drop-down list. The values populated in this field are based on the configurations done on Asset Return Type page. (See Asset Return Type).
Number of Approvals	Select the number of approvals from the list. Based on the number of approvals selected, the Level fields appear to select an Approver for the level.
Level	Displays level(s) based on the value in Number of Approvals selection.
Approver Type	Select the Approver for each level from the list.
Asset condition check Required	Select this check box to validate Asset condition for Asset movement.
Select Store location – Update	If selected, the approver at respective level can update the return store location for the asset.
Enable Print Gate Pass	If the check box is selected, the Print Gate Pass option is displayed on the Movement Approval page.
Enable Default store	If the check box is selected, the default store will be populated in the Asset Drop location on the Asset Return List pop-up page for the end user while initiating the return movement for asset.
Active	Indicates the status set for an Asset movement configuration. If selected, the Asset Movement Approval Matrix is active. If not selected, the Asset Movement Approval Matrix is inactive.

Default Type Movement

If movement type is selected as Default Type Movement, the following fields are displayed as shown in the figure below:

Figure: MOVEMENT CONFIGURATION page (Default Type Movement)

Field Description for Default Type Movement

The following table describes the fields on the Default MOVEMENT CONFIGURATION page:

Field	Description
DETAILS
Type	Lists the configured Asset Movement types. Select a type from the list. All: Select this option to configure approvals for all movement. Floor: Select this option to configure approvals for Floor movement of the Asset. From Repair: Select this option to configure approvals for Asset Movement from Repair. Store: Select this option to configure approvals for Store Movement of the Asset. To Repair: Select this option to configure approvals for Asset Movement to Repair.
Number of Approvals	Select the number of approvals from the list. Based on the number of approvals selected, the Level fields appear to select an Approver for the level.
Level	Select the Approver for each level from the list.
Asset Validation Required	Select this check box to validate Asset for Asset movement.
Active	Indicates the status set for an Asset movement configuration. If selected, the Asset Movement Approval Matrix is active. If not selected, the Asset Movement Approval Matrix is inactive.

ACTIONS

This section explains all the icons displayed on the ACTIONS panel of the MOVEMENT CONFIGURATION page. By default MOVEMENT CONFIGURATION page displays the list of Asset Movements already configured for the selected tenant. Refer the figure below.

Figure: MOVEMENT CONFIGURATION page: List of Asset Movement configurations

Click ADD NEW to configure new Asset Movement for the selected Tenant.

SHOW LIST

Click SHOW LIST.

Figure: MOVEMENT CONFIGURATION page

This displays the LIST table showing all the configured Asset Movements for the selected Tenant.

Figure: MOVEMENT CONFIGURATION page: List of Asset Movement configurations

To update an Asset Movement, click the required Movement Type. Make appropriate changes and click SUBMIT.
To display the inactive Asset Movement, click the Include Inactive check box.

When the Asset Movement is displayed under the LIST table, the ADD NEW action is displayed on the ACTIONS panel. Click ADD NEW to configure the Asset Movement.

LOCATION-WISE APPROVER

Click to configure Location-wise Approvers. For more information about Location-wise Approvers, see Configuring Location-wise Approvers.

APPROVAL CONFIGURATION

Click to configure Category-wise Approvals.

Figure: APPROVAL CONFIGURATION page

Select the Asset Movement Types (Floor, Store, From Repair, To Repair) under Enable Approval column for each asset category listed as per the requirement.
Click SUBMIT.

LOCATION AND STORE

Click to configure the default store. For more information on setting up a store as default, see Location And Store Configuration.

Custom Scheduler Jobs

The following Custom Scheduler Job should be enabled for Asset Movement configurations to function correctly:

Movement Returnable Asset: Asset movement with returnable type asset alerts. This job should be configured on 
the SummitAI Application Server. It is recommended to schedule this job to run once every day.

TahoeSP3