87928

On the Incident List page, the records were not displayed as per the Response / Resolution SLA selection on the Filter Pop-up. The Incidents with Response / Resolution SLA values of more than 100% and less the 75% were included in the record.

This issue occurred when on the FILTER pop-up, the Response / Resolution SLA attribute is set as > 75% about to miss.

Now, the records are displayed as per the Response / Resolution SLA selection on the Filter Pop-up.

Issue

The following two known issues are observed:

• Duplicate Incidents are getting created while monitoring various parameters except for the CPU and Memory utilization. This issue occurs when an Analyst tried to resolve the Incident manually.
• After configuring the Number of Polling on the ACTION TEMPLATE page, the Incidents are logged, and assigning incorrect Incident for the Events.

For Example:
Consider the utilization threshold values for Low, Medium, and High as 60%, 70%, 80% and Number of Polling for Incident Logging as 2. After the first polling there is a breach in Low threshold value and event gets created. On second polling there is High level breach and a critical event gets created.

The issue is, after the second polling an Incident is logged for the Low threshold breach and assigning the Incident to the Critical Event of the High threshold breach.

The Username, E-mail ID, Emp Id, and values for few of the columns are not displayed in the columns under the DEALLOCATED ASSETS section on the ASSET DETAILS pop-up page when the Checker refers back Assets of Deallocation Transaction type.(#67805)

Precondition:

1. Make sure that the Asset is allocated to Single User with Maker-checker.
2. Make sure that the Asset is sent for Deallocation and Checker refers back the Asset.

Bug Reproduction Steps:

1. Log into the Application.
2. Select Reports > Asset >Maker-checker Dashboard.
3. On the FILTERS pop-up page, select a Tenant, Location, and specify Referred Back in the Status. Click SUBMIT.
4. On the MAKER-CHECKER DASHBOARD page, click Deallocated count hyperlink.
5. Check the Username and E-mail ID for the Asset. The Username, Email ID, Emp id and values for few of the columns are not displaying under the DEALLOCATED ASSETS section on the ASSET DETAILS pop-up page

On the FIXED ASSET INVENTORY page, only added Assets with Maker Checker configuration are displayed when Referred Back is selected in the Checker Status drop-down list on the FILTERS pop-up page. (#65848).

Required configuration:

1. Log into the Application
2. Select Admin > Infrastructure > Tenant.
3. On the TENANT LIST page, select a Tenant.
4. On the TENANT page, click CONFIGURE DETAILS under ACTIONS panel.
5. Select ASSET MANAGEMENT under MODULES.
6. Select Enable Maker-Checker check box.

 Bug Reproduction Steps:

1. Select Asset > Manage Assets > Asset Inventory.
2. On the ASSET INVENTORY page, select FIXED under SELECT THE ASSET TYPE.
3. On the FIXED ASSET page, select a Tenant.
4. On the FILTERS pop-up page, select Referred Back in the Checker Status drop-down list. Only the added Assets with Maker Checker configuration are displayed.

On the ADMIN DETAILS page (Admin > Advanced > Password Management > Administrator > Click ADD NEW on the ACTIONS panel > Specify all the details > Click SUBMIT > Select the Domain Name on the LIST page), the Password field is not displaying the GUID or Encrypted ID of the password and the field is empty. This issue is found when the user is logging into the SummitAI application using Microsoft Internet Explorer browser.

On the Incident Management FORM BUILDER page (Admin > FORM BUILDER > Select a Tenant > Select Module as Incident Management > Click Add on Actions panel> Select Display At as Additional Information or General Area or TFS Area > Click Next), when a user configures single Parent and multiple Child using Common Master, the collective values of both Child 1 and Child 2 are displayed in Child 1 and Child 2 drop-down lists.

On the Service Request Management FORM BUILDER page (Admin > FORM BUILDER > Select a Tenant > Select Module as Service Request > Click Add on Actions panel> Select Display At as Additional Information or General Area or TFS Area > Click Next), when a user configures single Parent and Multiple Child using Common Master, the collective values of both Child 1 and Child 2 are displayed in Child 1 and Child 2 drop-down lists.

Overlapping of content is observed on the Pagination bar of all the pages having lot of records (typically in the range of 5 digits).

The configured Bulletin Board (Admin > Advanced > Notifications > Bulletin Board > Select the Tenant > Click ADD NEW to configure the Bulletin details > Click SUBMIT) is displayed on the END USER DASHBOARD page even if the user does not have access to the selected Tenant and Domain.

Broken image of the logo is displayed in the application when the logo image is deleted from the APPLICATION SETTINGS page (Admin > Basic > Infrastructure > Application Settings).

Workaround: The users need to re-login to the SummitAI application after deleting the logo.

On the AUTO-RESOLUTION SERVICE REQUEST CONFIGURATION and AUTO-RESOLUTION INCIDENT CONFIGURATION page (Admin > Basic > Infrastructure > Tenant > Select Domain > Select Tenant which is configured with Service Request/ Incident Management module > Click CONFIGURE DETAILS on the ACTIONS panel > Under the For End Users tab, select a reason form the Enable Reminder to Callers for Pending Reasons drop-down list > Enable Auto-Resolve Service Requests/ Auto-Resolve Incidents check box > Click Set Fields for Auto-Resolving Service Requests/ Set Fields for Auto-Resolving Incidents link), the users can set the auto-resolution criteria by specifying only white space (not numbers and alphabets) in the Response SLA Reason, Resolution SLA Reason, and Solution fields.

The following issues are observed in BI Custom Reports:

• When a user downloads the report (in any format), the data is displayed with hyperlinks.
• When a user places the mouse cursor on the count link, the tooltip is displayed as [Object Object].
• In the exported report, report name is displayed with '+' instead of space.

The Change Record is not created when the CR Requester and Customer Approver are same. This issue occurs even though Do Not allow Customer Approval of CR check box is selected on the Change Management TENANT configuration page. This issue occurs only for the first time when the Tenant is configured.

Workaround: The Administrator needs to unselect and again select the Do Not allow Customer Approval of CR on the Change Management TENANT configuration page (Admin > Basic > Infrastructure > Tenant > Select the respective Tenant for which this issue is occurring > Click CONFIGURE DETAILS on the ACTIONS panel > Enable Do Not allow Customer Approval of CR check box and click SUBMIT > Clear Do Not allow Customer Approval of CR check box and then click SUBMIT, again).

The new SLA Value of an Incident is not displayed on the CHANGE HISTORY pop-up page (Incident > User > Manage Incidents > Incident List > Select the required Incident ID from the list > Click CHANGE HISTORY on the ACTIONS to view the change history of the selected Incident) when an incident is moved from New status to In-Progress using Notification Services.

The Pending Reason of an incident is still displayed on the CHANGE HISTORY pop-up page (Incident > User > Manage Incidents > Incident List > Select the required Incident ID from the list > Click CHANGE HISTORY on the ACTIONS to view the change history of the selected Incident), when an Orchestration Script fails and the respective Incident is moved back from Pending to In-Progress.

The notification e-mails related to escalation and jobs are triggered only in English language irrespective of the configured language on the NOTIFICATION TEMPLATE page for all the modules (Admin> Advanced> Notification> Notification Template> Select a Tenant > Click ADD NEW > Specify all the required fields > Click SUBMIT).